1.Description
This module is used in conjunction with the DCS IP gateway (Gira Order No. 2620 ..).
It evaluates whether a voice message on a door station by the Gira HomeServer (logic node: Send/Door station voice message) is confirmed by the DCS IP gateway.
Input 2 (bus address) acts here as a filter, i.e., only telegrams are evaluated which match the filter properties.
If successful, the module at Output 1 sends a 1 telegram.
In the case of an error, Output 1 sends a 0 telegram.
It evaluates whether a voice message on a door station by the Gira HomeServer (logic node: Send/Door station voice message) is confirmed by the DCS IP gateway.
Input 2 (bus address) acts here as a filter, i.e., only telegrams are evaluated which match the filter properties.
If successful, the module at Output 1 sends a 1 telegram.
In the case of an error, Output 1 sends a 0 telegram.
Note
The module requires the firmware version of the DCS IP gateway 3 or higher!
2.Inputs
| No. | Name | Initialisation | Description |
|---|---|---|---|
| 1 | Door communication Receive | "" | (14 bytes – Text) Here the internal communication object Door communication Receive is assigned by the DCS IP gateway. |
| 2 | Bus address | "" | (14 bytes – Text) Optional specification of a bus address to which filtering should be applied. The bus address must have the following format: Example: 0xABCD07 or 0x42A305 Note If this input remains free, the telegrams of random bus addresses are evaluated. If a communication object is assigned but is not written to or provided with an initialisation value, then the object is considered not to be set. This means the incoming telegrams of all bus addresses are evaluated. |
3.Outputs
| No. | Name | Initialisation | SBC | Description |
|---|---|---|---|---|
| 1 | Voice message successful | 0 | s | (1 Bit) The voice message triggered on the door station via the Gira HomeServer logic node is confirmed with a 1-telegram if successful. In the case of an error a 0-telegram is sent. |
| 2 | Bus address | "" | s | (14 bytes – Text) Output of the bus address in the format: 0xABEF07 |
| 3 | Current status | 0 | s | (-255 to 255) The output sends the current status of the voice message. 0 = The voice message(s) are played 1 = The voice message(s) was/were played back successfully. The conversation has ended. -1 = The door station does not respond -2 = Voice message cancelled because of external event -3 = The max. playback time (max. 2 min) was exceeded by the total voice messages -4 = The voice message ID is unknown |
| 4 | Number of unknown voice message ID | 0 | s | (1 byte: 0-255) The output provides the number of the unknown voice message ID (value range 0 to 255). |
| 5 | Error output | 0 | s | (1 byte: 0-255) The output can be routed to the outside as a diagnostic output if necessary or during start-up in order to obtain information about possible errors. Values in the value range of 0 to 3 are sent. 0 = An error has not occurred. 1 = Check the length of the bus address 2 = Check the characters of the bus address 3 = A telegram with another structure was received. |
s = send, sbc = send by change
4.Other
| Recalculation during start: | No |
|---|---|
| Module is retentive: | No |
| Internal designation: | 16941 |
| Category: | Door communication\Receive |
5.Similar functions
Receive
Switching action
Floor call
Internal call
Door call (incl. bell symbol on code keypad)
Switching action Keyless In
Door opener command
Door opener command of device with KeyLess In
Light function
Evaluation Sabotage KeyLessIn
Evaluate status automatic door opener DCS Communicator
Button event DCS Communicator
Button event home station/TC gateway
Evaluate status of forwarding
Response - Evaluate status of JPEG image call
Evaluation of sabotage control device
Floor call
Internal call
Door call (incl. bell symbol on code keypad)
Switching action Keyless In
Door opener command
Door opener command of device with KeyLess In
Light function
Evaluation Sabotage KeyLessIn
Evaluate status automatic door opener DCS Communicator
Button event DCS Communicator
Button event home station/TC gateway
Evaluate status of forwarding
Response - Evaluate status of JPEG image call
Evaluation of sabotage control device
Receive\Evaluate code from code keypad
Universal filter function with code specification as text
Universal filter function with code specification as value
Universal filter function with code specification as value
Send
Light function
Switching action
Query/set automatic door opener DCS Client
Door station voice message
Query/set forwarding
Terminate call status of DCS bus devices
Switching action
Query/set automatic door opener DCS Client
Door station voice message
Query/set forwarding
Terminate call status of DCS bus devices
Additional modules